Product description
- 0...100 % RH (Humidity) – 35...+80 °C / – 31...+176 °F (Temperature)
- Modbus
- Protection type: IP 65
International system of units SI (default) can be switched to Imperial (via Modbus).
The showcase sensor is used in non-aggressive, dust-free environments and is specifically designed for installation in ceilings, walls, inside showcases or display cabinets in museums, galleries, cinemas, lecture halls or laboratories.
A long-term stable, digital humidity and temperature sensor guarantee exact measurement results.
These measurands are used to internally calculate the following parameters that can be retrieved via Modbus: relative humidity, absolute humidity, mixture ratio, dew point, enthalpy (ignoring atmospheric air pressure) and ambient temperature.
Modbus sensor SD with RS485 Modbus interface (not galvanically isolated), selectable bus termination resistance, DIP switch for setting the bus parameters and bus address in current-free state, internal LEDs for telegram status display, Display with illumination, individually programmable.
Uses internal diagnostics to detect sensor breakage or sensor short circuit as errors.
The sensor is factory-calibrated; an environmental precision adjustment by an expert is possible.
Technical data
| Voltage supply | 24 V AC (± 20 %) and 15…36 V DC (± 10 %) |
| Power consumption | < 1.0 W/ 24 V DC < 2.2 VA/ 24 V AC |
| System of units | SI (default) or Imperial (switchable via Modbus) |
| Data points | Temperature [°C] [°F] Relative humidity [% RH] Dew point [°C] [°F] Absolute humidity [g/m3] [gr/ft3] Mixing ratio [g/kg] [gr/lb] Enthalpy [kJ/kg] [Btu/lb] |
| Sensor | digital humidity sensor with integrated temperature sensor low hysteresis high long-term stability |
| Measuring range, humidity | 0...100 % RH (Humidity) – 35...+80 °C / – 31...+176 °F (Temperature) |
| Accuracy in humidity | typical ± 2.0 % (20...80 % RH) at +25 °C otherwise ± 3.0 % |
| Accuracy temperature | typical ± 0.6 K at +25 °C |
| Zero point offset | ± 10 % RH (Humidity) ± 10 K(Temperature) |
| Ambient temperature | –30...+70 °C |
| Medium | clean air and non-aggressive non-combustible gases |
| Bus interface | RS 485 not galvanically isolated bus termination activatable via DIP switches. Up to 32 devices possible in one segment. In case of a greater number of devices RS485 repeaters must be used. |
| Bus protocol | Modbus (RTU mode) address range 0...247 selectable |
| Baud rate | 9600 19200 38400 Baud |
| Status display | LED green = Telegram valid LED red = Telegram error |
| Signal filtering | 4 s / 32 s |
| Sensor protection | Probe made of stainless steel V4A (1.4571) pluggable sensor head Ø = 17 mm H = approx. 2.5 mm protective sleeve Ø = 10 mm NL = approx. 25 mm M10 x 1.0 with plastic plug connector Ø = approx. 11 mm NL = approx. 25 mm |
| Mounting | Cut-out Ø = 11 - 15 mm inserted length (EL) = approx. 50 mm lock nut for fixing is included in the scope of delivery. |
| Connection cable | PVC LiYY 4 x 0.14 mm² cable length (KL) = 2 m |
| Housing | Plastic UV-resistant material polyamide 30 % glass-globe reinforced with quick-release screws (slotted/ Phillips head combination) colour traffic white (similar to RAL 9016) cover for display is transparent! |
| Housing dimension | 72 x 64 x 43.3 mm (Tyr 1 with display) |
| Cable connection | Cable gland plastic 2x M 12 x 1.5 (Y-adapter) with strain relief exchangeable max. inner diameter 6 mm |
| Electrical connection | 0.14 - 1.5 mm2 via terminal screws |
| Long-term stability | ± 1 % per year |
| Permissible humidity | < 95 % RH non-precipitating air |
| Protection class | III (according to EN 60 730) |
| Protection type | IP 65 (according to EN 60 529) Housing tested TÜV SÜD Report No.713139052 (Tyr 1) |
| Standards | CE conformity according to EMC Directive 2014/ 30/ EU |
| Optional | Display with illumination two-line programmable cutout approx. 36 x15 mm (W x H) for displaying the actual temperature error message or an individually programmable display value |
W-Modbus: Pairing a Field Device with a Gateway
In this video setup guide, we'll show you how to connect a gateway to a...
W-Modbus: Pairing a Field Device with a Gateway
In this video setup guide, we'll show you how to connect a gateway to a field device via W-Modbus...
Wireless BACnet (W-BACnet) – Wireless Building ...
Author: T. Graf The demands placed on modern building automation are constantly growing. Buildings are...
Wireless BACnet (W-BACnet) – Wireless Building ...
Author: T. Graf The demands placed on modern building automation are constantly growing. Building...
BACnet – The Open Communication Standard
Author: T. Graf Modern buildings are becoming increasingly intelligent. Sensors measure temperature, humidity, and CO₂...
BACnet – The Open Communication Standard
Author: T. Graf Modern buildings are becoming increasingly intelligent. Sensors measure temperatu...
Humidity Sensors for Animal Husbandry and Agric...
In our previous post, we already explained the specific demands that high humidity and near-condensation...
Humidity Sensors for Animal Husbandry and Agric...
In our previous post, we already explained the specific demands that high humidity and near-conde...
Humidity Sensors for Swimming Pools and Spa Areas
In our previous article, we described the specific challenges that high humidity, condensation, and harsh...
Humidity Sensors for Swimming Pools and Spa Areas
In our previous article, we described the specific challenges that high humidity, condensation, a...
High-Humidity Sensors in Industry & Manufacturing
In our previous post, we described the challenges that high humidity, condensation, and harsh environmental...
High-Humidity Sensors in Industry & Manufacturing
In our previous post, we described the challenges that high humidity, condensation, and harsh env...
High-humidity sensors in the food industry and ...
High humidity places special demands on the sensors used in many applications. In our previous...
High-humidity sensors in the food industry and ...
High humidity places special demands on the sensors used in many applications. In our previous ar...
Humidity and Temperature Sensors for Harsh Envi...
Author: S. Becker In many applications, humidity is not the actual problem—it is air quality....
Humidity and Temperature Sensors for Harsh Envi...
Author: S. Becker In many applications, humidity is not the actual problem—it is air quality. Che...
High-humidity sensors for the pharmaceutical in...
In this article, we’ve explained in detail why humidity measurement is essential under high-humidity conditions...
High-humidity sensors for the pharmaceutical in...
In this article, we’ve explained in detail why humidity measurement is essential under high-humid...
We also manufacture individually
Do you have special requirements? As a manufacturer with our own production facilities in Germany, we are always in a position to produce products outside the standard range.
Contact us
Secure payment methods
Do you have a question? We are at your disposal:
Mo. - Fr. 7.00am - 5.00pm CEST