
Product description
- Measuring range: – 50...+ 150 °C / – 58...+ 302 °F
- Output: Modbus
- Protection type: IP 65
Calibratable temperature measuring transducer with sleeve sensor THERMASGARD® HFTM-Modbus-SD, with Modbus connection (Y-adapter), in an impact-resistant plastic housing resistant plastic housing with quick-locking screws, cable sensor with a stainless steel sleeve, measures temperature (–50...+150 °C / – 58...+ 302 °F).
The sleeve sensor is used to detect the temperature in liquid and gaseous media. It is used as a duct sensor or, if installed in immersion sleeve THE (accessories), as an immersion and screw-in sensor in liquids.
Modbus sensor SD with RS485 Modbus interface (not galvanically isolated), selectable bus termination resistance, DIP switch for setting the bus parameters and bus address in current-free state, internal LEDs for telegram status display.
Uses internal diagnostics to detect sensor breakage or sensor short circuit as errors. The sensor is factory-calibrated; an environmental precision adjustment by an expert is possible.
The sleeve sensor is used to detect the temperature in liquid and gaseous media. It is used as a duct sensor or, if installed in immersion sleeve THE (accessories), as an immersion and screw-in sensor in liquids.
Modbus sensor SD with RS485 Modbus interface (not galvanically isolated), selectable bus termination resistance, DIP switch for setting the bus parameters and bus address in current-free state, internal LEDs for telegram status display.
Uses internal diagnostics to detect sensor breakage or sensor short circuit as errors. The sensor is factory-calibrated; an environmental precision adjustment by an expert is possible.
Technical data
| Voltage supply | 24 V AC (± 20 %) and 15…36 V DC (± 10 %) |
| Power consumption | < 1.0 W/ 24 V DC < 2.2 VA/ 24 V AC |
| System of units | SI (default) or Imperial (switchable via Modbus) |
| Data points | Temperature [°C] [°F] |
| Sensor | Pt1000 DIN EN 60751 class B (Perfect Sensor Protection at IP 68) |
| Measuring range | – 50...+ 150 °C / – 58...+ 302 °F |
| Accuracy temperature | typical ± 0.2 K at +25 °C |
| Insulating resistance | ≥ 100 MΩ at +20 °C (500 V DC) |
| Zero point offset | ± 10 K |
| Ambient temperature | Measuring transducer –30...+70 °C |
| Medium | clean air and non-aggressive non-combustible gases liquids depending on selected immersion sleeve (accessory) |
| Error detection | Sensor breakage sensor short circuit |
| Bus interface | RS 485 not galvanically isolated bus termination activatable via DIP switches. Up to 32 devices possible in one segment. In case of a greater number of devices RS485 repeaters must be used. |
| Bus protocol | Modbus (RTU mode) address range 0...247 selectable |
| Baud rate | 9600 19200 38400 Baud |
| Status display | LED green = Telegram valid LED red = Telegram error |
| Signal filtering | 0.3 s / 1 s / 10 s |
| Sensor protection | Sensor sleeve made from stainless steel V4A (1.4571) Ø = 6 mm nominal length (NL) = 50 mm (optional 30...400 mm) |
| Sensor cable | Silicone SiHF 2 x 0.25 mm² cable length (KL) = 1.5m (other lengths and jacket materials, e.g. PTFE or glass fibre with steel mesh, available on request) |
| Housing | Plastic UV-resistant material polyamide 30 % glass-globe reinforced with quick-locking screws (slotted/ Phillips head combination) colour traffic white (similar to RAL 9016) housing cover for display is transparent! |
| Housing dimension | 72 x 64 x 37.8 mm (Tyr 1 without display) |
| Cable connection | Cable gland plastic 2x M 12 x 1.5 (Y-adapter) with strain relief exchangeable max. inner diameter 6 mm |
| Electrical connection | 0.14 - 1.5 mm² via terminal screws |
| Process connection | by screws |
| Permissible humidity | < 95 % RH non-precipitating air |
| Protection class | III (according to EN 60 730) |
| Protection type | IP 65 (according to EN 60 529) housing tested TÜV SÜD Report No. 713139052 (Tyr 1) |
| Protection type sensor | IP 65 (according to EN 60 529) sleeve humidity-tight (standard) IP 68 (according to EN 60 529) sleeve water-tight (optional) IP 54 (according to EN 60 529) with glass fibre cable (optional) |
| Standards | CE conformity according to EMC Directive 2014/ 30/ EU |
We also manufacture individually
Do you have special requirements? As a manufacturer with our own production facilities in Germany, we are always in a position to produce products outside the standard range.
Contact us
Secure payment methods
Do you have a question? We are at your disposal:
+49 911 519 470
Mo. - Fr. 7.00am - 5.00pm CEST