Pressure sensor for differential pressure and volume flow PREMASGARD 714x - Modbus
Log in

Advantages of a customer account

  • Individual conditions
  • Individual payment methods
  • Overview of all orders
  • User administration
  • Document archive
Back to article overview
temperature Pressure + calculated values

Pressure sensor and measuring transducer for differential pressure and volume flow, with Modbus connection, with automatic zero-point calibration PREMASGARD® 714x - Modbus

Product group: WG02

Low availability.

Usually ships in 3 to 5 days
360,92 €
429,49 € incl. VAT + shipping

Description

Pressure sensor and measuring transducer for differential pressure and volume flow, with Modbus connection, with automatic zero-point calibration PREMASGARD® 714x - Modbus
Maintenance-free, microprocessor-controlled PREMASGARD® 714x - Modbus (series) with Modbus connection, in an impact-resistant plastic housing with quick-locking screws, connection nozzles for pressure hose (Ø 6 mm), with cable gland or M12 connector according to DIN EN 61076-2-101, optionally with/without display, for measuring the differential pressure (max. ± 7000 Pa) in air. International system of units SI (default) can be switched to Imperial (via Modbus). Incl. mounting flange and connection set ASD-06 (2 m connecting hose, two pressure port nipples, screws).

The pressure sensor is applied to measure positive, negative or differential pressure in clean air and gaseous media. It is used in the clean room, medical and filter technology, ventilation and air conditioning ducts, spray booths, large-scale catering facilities, for filter monitoring and level measurement or for triggering frequency converters. A pressure sensor with piezoresistive measuring element guarantees exact measurement results. The following measured values can be accessed via the Modbus: Differential pressure, volume flow.
Innovative Modbus sensor with galvanically separated RS485 Modbus interface, selectable bus termination resistance, DIP switch for setting the bus parameters and bus address in current-free state, internal LEDs for telegram status display, two separate push-in terminals and large three-line display (illuminated; with customised programming in the 7-segment and dot-matrix range). The sensor is factory-calibrated; an environmental precision adjustment by an expert is possible.

Technical details

Voltage supply
24 V AC (± 20 %) and
15…36 V DC
Power consumption
< 4.8 W/ 24 V DC typical; < 6.8 VA/ 24 V AC typical
Data points
Differential pressure [Pa],
volume flow [m3/h]
Controlled medium
clean air and
non-aggressive, non-combustible gases
Media temperature
–20...+50 °C (temperature-compensated 0...+50 °C)
Pressure connection
with metal connection nozzles for pressure hose Ø 6 mm
Type of pressure
differential pressure
Zero point offset
± 10 % measuring range
Above- below-pressure
máx. ± 50 kPa
Ambient temperature
–30...+70 °C
Bus protocol
Modbus (RTU mode),
address range 0...247 selectable
Signal filtering
0 s / 1 s / 10 s
Electrical connection
0.2 - 1.5 mm², via push-in terminal
Cable connection
cable gland, plastic (M 16 x 1.5; with strain relief, exchangeable, max. inner diameter 10.4 mm) or
M12 connector according to DIN EN 61076-2-101 (optional on request)
Housing
plastic, UV-stabilised,
material polyamide, 30 % glass-globe reinforced,
with quick-locking screws
(slotted/ Phillips head - combination),
colour traffic white (similar to RAL 9016),
housing cover for display is transparent !
Housing dimensions
126 x 90 x 50 mm (Tyr 2)
Long-term stability
± 1 % per year
Hysteresis
0.3 % of final value
Media contacting parts
Brass, Ni, Duroplast, Si, epoxy, RTV, BSG, UV silicone gel
Temperature drift values
± 0.1 %/ °C
Linearity
< ± 1 % of final value
Humidity
0...95 % RH (without dew formation)
Protection class
III (according to EN 60 730)
Protection type
IP 65 (according to EN 60 529) in the built-in state
Units
switchable metric / imperial