Sleeve sensor with temperature measuring transducer (cable temperature measuring transducer) THERMASGARD® HFTM-U LCD

Display

IP protection class

output model

output

Item no. 1101-1151-2219-920

EAN 4251325600673

Product group: WG01

Sleeve sensor with temperature measuring transducer (cable temperature measuring transducer) THERMASGARD® HFTM

Calibratable THERMASGARD® HFTM temperature measuring transducer with sleeve sensor with eight switchable measuring ranges, continuous output, housing made of impact resistant plastic with quick-release screws, optionally with/without display, with cable gland or M12 connector according to DIN EN 61076-2-101.

The temperature transmitter with remote sensor serves to detect temperatures in liquid and gaseous media, e.g. if installed in a thermowell or as a duct sensor. A direct, permanent use in liquids is possible in combination with our THE thermowells (accessory).The sensor is factory-calibrated and can be fine-tuned to ambient conditions by an expert.

Power consumption

< 1,0 W/ 24 V DC
< 2,2 VA/ 24 V AC

Deviation of humidity

typically ± 0.2 K at +25 °C

Voltage supply

24 V AC/ DC (± 10 %)

Temperature deviation

typically ± 0.2 K at +25 °C

Load resistance

RL > 5 kOhm

Sensor

Pt1000, DIN EN 60751, class B

Connection type

2- or 3-wire connection

Ambient temperature

Measuring transducer –30...+70 °C

Insulating resistance

100 MΩ,
at +20 °C (500V DC)

Electrical connection

0.14 - 1.5 mm²
via terminal screws on circuit board

Cable gland

M 16 x 1.5, including strain relief, exchangeable,
max. inner diameter 10.4 mm

Permissible air humidity

< 95 % RH, non-precipitating air

Protection class

III (according to EN 60 730)

Output

0 - 10 V

Sensor protection

sensor sleeve, stainless steel V4A (1.4571), Ø = 6 mm,
nominal length NL = 50 mm (other dimensions optionally available)
cable entry stamped (optionally rolled)

Measuring ranges

multi-range switching with 8 switchable measuring ranges,
see table (other ranges optional)
with manual zero point correction (± 10 K)

Sensor protection

stainless steel, 1.4571, V4A, Ø = 6 mm,
nominal length (NL) = 50 mm
(other dimensions optional)
cable entry stamped (optional rolled)

Cable connection

cable gland, plastic (M 16 x 1.5; with strain relief, exchangeable, max. inner diameter 10.4 mm) or
M12 connector according to DIN EN 61076-2-101 (optional on request)

Housing

plastic, UV-stabilised,
material polyamide, 30 % glass-globe reinforced,
with quick-locking screws
(slotted/ Phillips head - combination),
colour traffic white (similar to RAL 9016),
housing cover for display is transparent !

Housing dimensions

72 x 64 x 43.3 mm (Tyr 1 with Display)

sensor cable

Silicone, SiHF, 2 x 0,25 mm²; cable length (KL) = 1.5m
(other lengths and jacket materials, e.g. PTFE or
glass fibre with steel mesh, available on request)

Protection type

IP 65 (according to EN 60 529) humidity-tight stamped
IP 68 (optional watertight compound-filled) rolled
IP 54 (optional glass fibre cable)

Protection type (sensor)

IP 65 (according to EN 60 529) sleeve humidity-tight (standard)
IP 68 (according to EN 60 529) sleeve water-tight (optional)
IP 54 (according to EN 60 529) with glass fibre cable (optional)

Protection type housing

IP 65 (according to EN 60 529) Housing tested,
TÜV SÜD, Report No.713139052 (Tyr 1)

Standards

CE conformity,
electromagnetic compatibility according to EN 61326,
according to EMC Directive 2014/ 30/ EU

Optional

display with illumination, two-line, cut-out approx. 36 x15 mm (B x H),
to display the actual temperature and internal diagnostics
(measuring range exceeded, measuring range not reached,
sensor breakage, sensor short circuit)

Display

Operating instructions

Catalogue page EN

CE - Declaration of Conformity

UKCA - Declaration of Conformity

CAD data

Tender text